Fluid Media Management System
This fluid media management system with a programmable control terminal and numerous functional modules ensures highest levels of occupational safety. One control terminal can be used to control several chemical storage cabinets and can be set up with various modules.
In its standard model version, the system allows selecting the components needed for a planned system from the following modules:
Identification module
which makes sure that only authorized persons are given access to the hazardous substances in question. In active storage mode, the media are released only subsequent to proper identification. This is implemented in the form of the input of a programmable PIN. The identification can also be implemented, upon request, with transponder keys or biometrical readers.
Air extraction monitoring module
which monitors the air extractions and triggers alarms as appropriate. The air extraction has to be always operating on cabinets that can go into active storage mode. When it is, it must constantly verify that there is a flow of extracted air and must alert to the problem whenever the airflow should fail. The air extraction monitoring module is a way to comply with this requirement, i.e. when extraction airflow fails, an alarm is triggered and a signal is sent, e.g., to the control center.
Dosing module
which enables exact filling. The dosing module turns the release of very small quantities of fluid media from large storage units into a process that it just as easy as it is safe. The ideal add-on to a COMPLEX Line drum station, there is the possibility, besides dosing, to ensure continuous analyses of consumed and remaining quantities.
Level sensing module
which alerts to the risk of overflowing storage units. The level sensor drastically reduces any risk of bringing too much media into a storage unit, and the safety of both the user and the environment increases accordingly. The level sensing module is the part that completes the perfect solution, DISPOSAL Line. Combining the DISPOSAL Line and the COMPLEX Line brings you the ideal preconditions to ensure easy and safe media management.
Door opening module
which opens the door when switched on at the keypad. When the command was entered and confirmed, an audible signal alerts the user to the door being opened. The control by compressed air does not have any electrical or electronic component, which makes it perfectly suited for explosive atmospheres.
Door locking module
which enables pairing door locking and door unlocking to user identification, thereby restricting access to the fluid media to those persons authorized to use them. In other words, access control for personnel can extend to the access to the chemical storage cabinets.
Related products
HWT 160 SW–E
HWT 160 SW–S
With the HÜRNER quick mounting system, the clamps can be replaced easy as ABC. The chassis/carriage, without the RH and LH pipe‑aligning clamps, can be removed from its steel frame by simply loosening 4 mounting screws and can then be used in areas that are hard to reach or overhead.
Both the operation of the clamps for the straight pipe and the saddle fitting and the movement of the carriage for the latter are implemented as using ergonomically designed handwheels. Additionally, the motion handwheel can be removed easily, to move the clamping chassis/carriage with a common power tool (cordless drill/screwdriver) as its drive.
A special mention deserve the heating element seat next to the chassis for clamping the saddle fitting, on which to place the heating element, and the two freely adjustable depth setpoints. The easy insertion and safe and swift removal of the heating element, including centering and an auto‑detaching step in the change‑over stage, bring a use as convenient as to be considered unique.
The insertion depth setpoints provide, on the one hand, consistent fusion depth and welding position and, on the other, shorter length of movements, thus faster change-over.
Special octagonal clamps for branch‑off fittings, of various wrench sizes, are also available.
Filter Units with Fan
Modular Protection System
Protect your chemical storage cabinet against unauthorized access, using the Modular Protection System (MPS). This system enables you to physically control the access to resources or hazardous substances in a state-of-the-art approach.
The identification ensures that only authorized persons are given access to the hazardous substances in question. This is implemented in the form of programmable PINs read from a transponder card by RFID technology. The identification can then be paired to the locking or the unlocking of the door of the cabinet. This means that the authorizations of personnel can extend to the storage cabinets as well.
The MPS is an important module to comply with increasingly tight requirements in terms of risk assessment as related to access control. In practical implementation, this may mean for you that work instructions providing for the safe and controlled use of hazardous substances can allow less complex routines, as, e.g., TRGS 526.
A functionality the MPS provides is the possibility to automatically close the door. This means that the cabinet takes care of door closing after the door was manually opened.
HWT 125 SW light
All-purpose socket welder for PP, PP-R, PVDF, PB, and PEHD fittings and pipelines in the range of dimensions from O.D. 20 - 125 mm, for professional overhead welding and operations in a confined space, yet also for standard workshop applications.
In its standard delivery, sockets and spigots size O.D. 63 - 125 mm are included, with O.D. 20 - 50 mm as an optional extra. With the HÜRNER quick mounting system, the clamps can be replaced easy as ABC. The clamping chassis can be removed from its steel frame by simply loosening 4 mounting screws and can, therefore, be used in areas that are hard to reach or overhead.
Both clamping the pipe and the fitting and moving the machine carriages are implemented as using ergonomically designed handwheels. Additionally, the motion handwheel can be removed easily, to move the carriages with a common power tool (drill / cordless screwdriver) as its drive. A special mention deserves the heating element seat of the clamping chassis, on which to place the heating element. The feature ensures easy insertion and safe removal of the heater, thereby providing reliable change-over management and convenient use that are unique in this category of welding systems.
Electrofusion With Report Logging
The WhiteLine welders cover all areas of application in electrofustion welding of PE, PP, and PVDF pipes with heater coil fittings. There is no challenge for which you will not find a welder of the series able to take it on successfully.
Wherever applicable, HÜRNER's all-purpose electrofusion welders have been developed in line with the requirements of the most recent version of the ISO standard 12176-2:2000, the DVS standard 2201-1, and the WEEE directive, with Reg. No. DE 74849106.
Whether it is jointing in the safety-sensitive area of gas networks, including accurate recording of geographic data, jointing components with very small diameters (e. g., geothermal or sanitary fitting applications) or very large diameters (e. g., wastewater applications)—the welders will always make a statement by their unyielding reliability that builds on more than 40 years of developing and manufacturing experience.The lighthouse products, HST 300 Pricon 2.0 and HST 300 Print+ 2.0, have an extremely intuitive data download menu enabling also transfer via Bluetooth, which allows downloading all welding and traceability data or a finely tuned selection of them, as an abstract or extended report in the PDF format, as a label tag printed with the optional printer, or as well in the DataWork format for processing on a PC.
HWT 250 MI
