Click to enlarge
Air Extractor with Fan
Air Extractor with Fan
Back to products
Filter Units with Fan
Filter Units with Fan

Extraction Monitor without Fan

This monitoring unit provides easy airflow monitoring of chemical storage cabinets. A sensor monitors the extraction airflow and triggers a visual and audible alarm when no airflow above the defined minimum is detected. The air monitoring unit without fan ships preassembled to be installed immediately on top of the storage cabinet. The alarm threshold for the airflow velocity is factory-set, but can be customized at the differential pressure meter/switch. The enclosure is made of silver pearl glimmer, powder-coated sheet steel. The airflow sensor monitors the actual extraction velocity and the entire extraction system of the storage cabinet.

Both the volumetric flow and the power supply are sensed by a microcontroller unit. When airflow velocity drops below the set threshold, visual and audible alarms are set off. The system ships with two potential-free (“dry”) contacts (24  V, 2 A) that can be used to send an alarm signal to the control center. An integrated battery cuts in in case of power supply failure, and the monitoring system and the display, including simple error messaging, can run on it for 4 hours. The product ships ready for plug-in.

Categories: ,
Description

Technical Specs

 

P/N 500-100… -106
Dimensions (W x H x D) 210 x 215 x 210 mm
Rubber sleeve 75 mm
Power supply 230 V, 50 Hz
Current input 0.1 A
ATEX-compliant under Dir. 2014/34/EU and Type Certificate issued by TÜV Süd
continued control pursuant to DIN EN 1946-7

Related products

HWT 500 CS

Request a Brochure
HÜRNER's HWT 500 CS  servo-operated workshop system is the end-to-end transformation of worksite technology into workshop systems. The system has been developed in compliance with the so-called machinery directive 2006/42/EC as amended and allows making segments, tees, Y pieces and crosspieces in workable dimensions from O.D. 200 (160) through 500 mm | 6" - 20". The welding system is set on a welded or a screwed-fast, heavy-duty, no-warp support frame and the bearings on which move both the horizontally traveling carriage and the heating element and facing tool assembly, are designed as precision-engineered and heavy load-bearing trapeze-shaped guides with precision-matched runner blocks. It goes without saying that all parameters that are critical for a high-quality and reproducible welded joint are monitored throughout the process and saved to the memory of the system, which can hold up to 10,000 reports. Furthermore, all CNC systems are equipped with a USB interface to enable downloading the welding reports in the PDF format to a USB stick or sending them to the management database in the HÜRNER DataWork Professional format. It is also possible to label a joint immediately for its quality by printing on plastic foil an indelible label tag with the available tag printer that will identify the fitting.

HWT 630 CS

Request a Brochure
HÜRNER's HWT 630 CS  servo-operated workshop system is the end-to-end transformation of worksite technology into workshop systems. The system has been developed in compliance with the so-called machinery directive 2006/42/EC as amended and allows making segments, tees, Y pieces and crosspieces in workable dimensions from O.D. 160 through 630 (500) mm | 6" - 24 (20)". The welding system is set on a welded or a screwed-fast, heavy-duty, no-warp support frame and the bearings on which move both the horizontally traveling carriage and the heating element and facing tool assembly, are designed as precision-engineered and heavy load-bearing trapeze-shaped guides with precision-matched runner blocks. It goes without saying that all parameters that are critical for a high-quality and reproducible welded joint are monitored throughout the process and saved to the memory of the system, which can hold up to 10,000 reports. Furthermore, all CNC systems are equipped with a USB interface to enable downloading the welding reports in the PDF format to a USB stick or sending them to the management database in the HÜRNER DataWork Professional format. It is also possible to label a joint immediately for its quality by printing on plastic foil an indelible label tag with the available tag printer that will identify the fitting.

Electrofusion Without Report Logging

Request a Brochure

The WhiteLine welders cover all areas of application in electrofustion welding of PE, PP, and PVDF pipes with heater coil fittings. There is no challenge for which you will not find a welder of the series able to take it on successfully.

Wherever applicable, HÜRNER's all-purpose electrofusion welders have been developed in line with the requirements of the most recent version of the ISO standard 12176-2:2000, the DVS standard 2201-1, and the WEEE directive, with Reg. No. DE 74849106.

Whether it is jointing in the safety-sensitive area of gas networks, including accurate recording of geographic data, jointing components with very small diameters (e. g., geothermal or sanitary fitting applications) or very large diameters (e. g., wastewater applications)—the welders will always make a statement by their unyielding reliability that builds on more than 40 years of developing and manufacturing experience.

HWT 250 MI

Request a Brochure
HÜRNER HWT 250 MI for manufacturing PE, PE 100 RC, PP, and PVDF1) pipes, segmented bends, and fittings. The design of the machine is such that pipes, segments O.D. 50 – 250 mm / 1½"– 8" with any SDR ratio up to SDR 11 can be processed. The system was developed under the machinery directive 2006/42/EC as amended, as far as applicable, and is set on a welded and bolted, totally heavy-duty support frame resistant to warping by design. Both the movable carriage of the system and the console carrying the heating element and the facing tool travel on precision-engineered, heavy load-bearing shafts and trapeze-shaped guides constructed with smoothly travelling runner blocks. Inserting the PTFE-coated heating element and the facing tool manually is as convenient as it is effortless. The swiveling master clamps on both sides can be rotated by up to 2 x 15 deg. (∢30 deg.) and also feature horizontal adjustability, to allow for compensating any misalignments. Heating element temperature control and facing tool operation are managed on the front panel. The practical wooden transport case serves both as a operating platform and as secure storage for the machine, the reducers, and the accessories.

HÜRNER LI Line CNC ECO

Request a Brochure
The HÜRNER LI Line CNC ECO is a high-quality and durable, next-generation CN-controlled plastic pipe butt-welding machine that has been developed in compliance, as applicable, with the machinery directive 2006/42/EC as amended as well as the ISO standard 12176-1 and the DVS standard 2207-1. The design of the machine is such that with 12 basic machine chassis models, pipes from O.D. (63) 75 through 355 mm can be jointed The welding machines ship with a fully encased CNC hydraulic and control box of ingress protection IP 54 managing pressures of up to 220 bar. Both the anti-stick-coated heating element and the facing tool are hooked up along with the machine chassis to the hydraulic and control unit. No additional power distribution is needed.

HÜRNER WhiteLine Manual Hydraulic

Request a Brochure
The Manual Hydraulic Series of butt-welding machines in the WhiteLine generation makes a statement by its superior manufacturing quality and its scalability in the form of an easy upgrade to a data logging-enabled machine with the installation of an SPG 2.0 data logger for welding report logging. The machine ships with a hydraulic unit that features, as a unique characteristic, a totally integrated enclosure that also is a splash and dirt shield for all components on the inside. The front panel controls, too, are included in the ingress protection according to the IP 54 rating (where IP 64 is possible upon request). All connections, including an additional power socket free to use for the operator’s convenience, are located at the back of the controller. Both the facing tool and the heating element are also connected at the back panel of the hydraulic controller. Therefore, no additional power distribution unit is needed. Industry version: Optionally, the machine chassis (250, 315, 355, 500, 630) are also available in an industry set-up with a modified 3rd clamp for clamping fittings with a short connecting stub.*) *) Retrofit kit for converting existing systems to industry version available upon request!

Air Extractor with Fan

Request a Brochure

This extractor provides easy airflow monitoring of chemical storage cabinets. The airflow monitoring unit with integrated fan ships preassembled to be installed immediately on top of the storage cabinet. The enclosure is made of silver pearl glimmer, powder-coated sheet steel

A sensor monitors the extraction airflow and triggers a visual and audible alarm when no airflow above the defined minimum is detected. The air monitoring unit fan ships preassembled to be installed immediately on top of the storage cabinet. The alarm threshold for the airflow velocity is factory-set, but can be customized at the differential pressure meter/switch. The airflow sensor monitors the actual extraction velocity and the entire extraction system of the storage cabinet. Both the volumetric flow and the power supply are sensed by a microcontroller unit. When airflow velocity drops below the set threshold, visual and audible alarms are set off. The system ships with two potential-free (“dry”) contacts (24  V, 2 A) that can be used to send an alarm signal to the control center. An integrated battery cuts in in case of power supply failure, and the monitoring system and the display, including simple error messaging, can run on it for 4 hours. The product ships ready for plug-in.

HÜRNER LI Line, the 4-3-2 Machine WeldControl

Request a Brochure
The handling of the HÜRNER 4-3-2 machine WeldControl is simply unique and it enables an approach to welding no other system is able to offer. Either the operator makes use of the assistance of the interactively responding hydraulic and control unit. Or the manual mode is selected to make the joint “by hand”. In the WeldControl mode the system walks the operator through the process after the pipe parameters were entered or confirmed. This includes monitoring the operator’s inputs and recording the entire process. WeldControl machines do not only provide presets, though; they facilitate the work, e. g., by reducing the pressure automatically when the automode was enabled. Welding reports have all data required by ISO traceability. In the Manual mode the display screen works as a digital gauge. It displays the welding pressures and heating element temperatures and is a one-stop provider of all data.